Kiln-room notes: the shelf tiles cropped the witness cones off the front rail

The first question on Friday was not about a glaze recipe. It was about a photograph. A member had her test bowl in one hand and pointed at the middle square on the firing board, asking whether that load had reached cone 6. I looked at the square with her. The bowls and the kiln wash were sharp. The front rail of the shelf, where I stand the witness cones so they can be read when the door comes open, had been cut away. The cones had gone with it.

I run the kiln room in a shared community studio. After every glaze firing I pin a row of shelf photographs beside the kiln, under the same strip of tape that holds the written log. One square per shelf, so someone coming in still dusty can find their work without me describing a foot ring in the corridor. The pockets on the board are square, which is the only reason the photographs have to be square.

Thursday's photographs were mine. I had shot each shelf from a slight angle, with the cone pack on the front rail and, when I could, the number painted on the post. Before I left, a volunteer offered to square them up so the pockets would sit evenly. In the morning the board looked neat and useless. The volunteer had cropped from the middle of each frame. The bowls survived. The cones did not. On the middle shelf the post number had gone as well. The camera card was still in the laptop. I opened Thursday's folder and there they were: a cone 6 slumped over, a cone 7 only beginning to tip. For the next twenty minutes I held the laptop up to anyone who came to the board, which is no way to run a kiln room.

What I do now is plain. I stop cutting. I put the original shelf photograph onto a larger square and let the extra canvas fall wherever the picture is short — at the sides for the usual tall shot, above and below if I happened to shoot wide. The cones remain on the rail. The pocket still gets a square.

The fill has to belong to the kiln, or the tile looks like a cutout. Our chamber is brown brick, dusted with kiln wash, darker in the element grooves. A band of printer-white down each side makes the shelf look lifted out of a catalogue. I pick a quiet patch of the real brick and continue it to the new edge. If a shadow sits under a post, I carry a soft version of it rather than a flat average of the wall. When the kiln door is already in the shot, I extend the steel, not the brick.

I also stopped saving over the camera file. The kiln-room laptop now keeps a dated folder of the pictures as they came off the card, and a second folder for whatever I actually print. That habit earned its keep when a member asked whether her test tile had sat near the elements or behind a larger bowl. I still had the original tall frame, made a fresh square with the cones and post number both visible, and reprinted one pocket, instead of reconstructing the load from memory while the kiln was still too hot to open.

Print size can undo a good decision. People read the board from a step away. A small phone file, pushed up to fill the pocket, turned the numbers on the cones into speck. I settle on a moderate square and tape a proof into the actual pocket, under the lip of tape, because a cone pack that looks safely inside the frame on a screen can vanish against the black edge of the board. If it is not readable on the door, it is not finished.

Some photographs cannot be saved by this method. A flattering picture of pots already cooling on the rack is not a firing tile. A shelf shot that never included the cones cannot grow them later. I send those back with a short request: the shelf as loaded, the witness cones on the front rail, and enough space around the cones that a later square will not eat them.

I nearly missed a second fault on the same load. The bottom shelf tile had lost the painted post number along the left edge. I only saw it when I held the print next to the original. Anything that lives near a border — a cone, a post number, a pencilled note on a test tile — is now the reason I take the picture, not an extra I can afford to drop.

I drop the tall photograph in, keep the whole shelf, and take a square away before the next load is ready to go. For that limited job, Square Image is the page I open on the kiln-room laptop. It runs in the browser, which suits a machine we do not load with extra software, and it will pad to a square with a sampled colour, a soft fill from the brick, or a plain border, instead of trimming the rail off. It cannot sharpen a cone the camera already blurred. It can keep the cones in the frame long enough for someone to read them without finding me first.

I do the work at the kiln-room counter now. If you keep a firing board or a loading log, look at the front edge before you accept the square. If the cones or the post number live there, add canvas from the real background, proof the tile where it will hang, and only then pin it up.

The firing board is not a catalogue of bowls. It is a record of the cones on the front rail. Leave room around those cones. Check the proof on the board. Then hang the tile, and then you can answer the first question of the morning without an apology.